|
*Why specify HoldTight®102 |
salt remover flash rust inhibitor |
? |
It KILLS Chlorides
and STOPS Flash Rust in One Pass. It Leaves No Residue. It's
Good to Coatings.
·
a
cost-effective alternative to single purpose, multi-step salt removal products
·
a coating-friendly
and effective alternative to old
fashioned nitrate, phosphate, film-forming, and solvent-based flash rust inhibitors
·
reams (or megabytes) of data and more than a decade of field experience to back it up
|
Texas
Oiltech Labs |
||
|
REMOVAL
METHOD |
CHLORIDE CONTENT µg/cm5 (measured
by total extraction method) |
|
|
|
BEFORE |
AFTER |
|
Dry Blast (sample 1) |
170.9 |
43.5 |
|
Wet Grit Blast (sample 2) |
488.2 |
35.9 |
|
Wet Grit Blast with HoldTight®102 (sample 3) |
534.4 |
Not Detected (<1.0) |
|
Wet Grit Blast with HoldTight®102 (sample 4) |
1,134.3 |
Not Detected (<1.0) |
|
Samples supplied by Occidental
Chemical Corp., Luling, LA. Report
and independent lab test data available on request. |
||
|
New
York City DoT |
||
|
REMOVAL METHOD |
CHLORIDE CONTENT ppm (measured
as shown) |
|
|
|
Quantab
Strips |
Kitigawa
Tubes |
|
None: original sample |
236 |
250 |
|
Power Tool only |
122 |
130 |
|
Power Tool + pressure wash, water only |
210 |
84 |
|
Power Tool + pressure wash, water
with HoldTight®102 |
32 |
14 |
|
Dry Blast only |
58 |
65 |
|
Dry Blast + pressure wash, water only |
41 |
20 |
|
Dry Blast + pressure wash, water with
HoldTight®102 |
Not Detected |
0 |
|
Samples supplied by and tested under
supervision of NYCDoT Bridge
Maintenance & Repair, Brooklyn, NY. |
||
When
Chlorides (or other contaminants)
are a problem, HoldTight®102 is a cost effective and reliable
solution. If Flash Rust is an issue, HoldTight®102 is THE answer. Cost
Conscious? Check out our dilution
ratios and consult us for estimating assistance. Using UHP? HoldTight®102 will end the “good rust” vs “bad
rust” dilemma and, used properly, will work with any equipment. If Coating
Compatibility is a concern: ask Ameron, Carboline, Dampney, Hempel, Keeler
& Long, PPG, Sherwin-Williams,
Sigma, Tnemec, Wasser or most any other coating supplier and compare to
other products: no nitrates, no phosphates, no solvents, no
film, no residue, non-acidic, neutral pH when applied.
HoldTight®102
has been tested for compatibility
with many different types of atmospheric
and immersion service coatings. Pull test values [p.s.i.] for typical coatings in a number of major categories are
shown below. Contact us for more.
|
INORGANIC ZINC, e.g., Carboline Carbo Zinc 11
[1084] ·
Sherwin-Williams ZincClad II HS [>2034] ·
Ameron Dimetcote 21-9 [>1050] |
|
ORGANIC ZINC, e.g., Carboline 858 [3030] & 859 [1798] · Sherwin-Williams ZincClad IV [>2034] |
|
POLYURETHANE & URETHANE, e.g., Sherwin-Williams Corothane I MC Tar [<2034] · Valspar
generic polyurethane [1079] |
|
EPOXY, e.g., Tnemec HS Epoxy series 104 [>2295] · Devoe Marine Phenolic Epoxy [>1050] · Ameron Amerlock 400 [>1050] |
|
POLYAMIDE EPOXY, e.g., Hempel Hempadur 1557, 4514, 4515, & 4563 [>1050] · Tnemec
Hibuild Epoxyline series 66
[2527] |
|
COAL TAR, e.g., Sherwin-Williams Corothane I MC Tar [>2034] · Carboline Bitumastic 300M [2266] |
|
ALKYD, e.g., Tnemec Chemprime HS series 37H [945] · Sherwin-Williams KemBond
HS Universal Primer [1306] |
Syed T. Hussain,
Technical Services
syed@holdtight.com
Peter J. Petkas, Sales & Marketing peter@holdtight.com